Sign in
Find the best local pros
See honest referrals, shared on social networks
Relevancy Ranking
Load more
?
Referral from March 27, 2017
Jacob D. asked:
Hey guys so I messed up big time...
I was trying to clear some melted pla from the hot end when it snapped and now I need to find replacement parts for the black piece...
Domenic D. replied:
found a very interesting good in Gearbest：Anet MK8 2 pcs Stainless Steel Nozzle Teflon http://m.gearbest.com/3 d-printer-parts/pp_540280.html
Justin H. replied:
If your looking for quick replacement https://www.amazon.com/gp/aw/d/B01DLQTBOU/ref=ya_aw_od_pi?ie=UTF8&psc=1 https://www.amazon.com/gp/aw/d/B01G1JWKQK/ref=ya_aw_od_pi?ie=UTF8&psc=1
Referral from September 20, 2017
Ben R. asked:
hi guys I'm looking for the best/cheapest replacement heat block for the A8 i just moved and the grub screw keeping the heating element in place disappeared (typical)...
Ben R. replied:
i found a lot of these basic ones http://www.ebay.co.uk/itm/3D-Printer-Anet-A8-A2-A6-Hotend-MK7-MK8-Extruder-Replacement-Heat-Block/122645521590 but not sure how affective they are going to be
Alan L. replied:
I just posted a piece on this group I got fully assembled hot ends from AliExpress: https://www.aliexpress.com/item/Professional-Assembled-MK8-Extruder-1-75 mm-0-4 mm-Nozzle-3D-Printer-Aluminum-Heating-Block-3D-Printing/32804834943.html
Referral from May 28, 2017
Simon R. asked:
I'm close to give up with my printer. :( Replaced stock: smooth rods, bearings, belts, heating block... and now my prints look like this. Any suggestions what can happen...
Swetha K. replied:
I have a strong feeling your issue is physical. The fact that you said it stared after changing the rods and bearings and switching to skynet didn't improve it, adds more weight to this assumption. Your answer might be fixing your z wobble. Print this and post back here: https://www.thingiverse.com/thing:680207 Print at 30 mm/s and 8 jerk so you can rule out print settings as a possible cause.
Konrad S. replied:
And its a good idea to take a closer look on Z threaded rods couplings : https://youtu.be/BLmfQ-KsVWs
Referral from July 24, 2017
Blaine M. asked:
So the heating wires for my hotbed are trying to light themselves on fire, and now look like this at the bed connection. Does anyone know where to get replacement wires,...
Denis V. replied:
http://printing.thorinair.net/post/162601751592/replacing-the-smoking-connector-of-doom Hope this helps :)
Drew L. replied:
http://www.ebay.com/itm/JST-VHR-6N-Harness-1 ft-2 ft-UL-Silicone-16AWG-cable-wire-for-amp-pre-amp-dac/222218285863
Referral from March 10, 2017
Lars D. asked:
After my first print I noticed that the hotbed not heating. This happened because the sensor input (H_T) of the hotbed seemed to be faulty (Look at the voltage). All...
Lars D. replied:
Just for information: https://goo.gl/T5PaoY It semes that I am not alone (in this group) with that problem.
Referral from January 14, 2017
Lars V. asked:
So, I went and tried to do my first ABS print, but I did not do the MOSFET upgrade first. So, halfway through the print, the bed (heated to 70) stopped heating and the...
Referral from March 24, 2017
Robert L. asked:
I have had my Anet A8 3D Printer for about 3 weeks now and no problems but today when I came back to a print the extruder heating element was on my build plate and...
Referral from March 27, 2017
Jacob D. asked:
Hey guys so I messed up big time...
I was trying to clear some melted pla from the hot end when it snapped and now I need to find replacement parts for the black piece...
Referral from March 30, 2017
Ryan O. asked:
My prints had been going great so I figured it was only a matter of time before I hit a hurdle.... Went to swap from ABS to PLA to print something yesterday and I think...
Referral from April 19, 2017
Ryan L. asked:
Has anyone ever experienced the extruder tip not heating up enough?
I am trying to reach 225 C for TPU but with the fan on, the tip won't reach that tempt. Even when i...
Referral from April 23, 2017
Joshua C. asked:
Crap.. I just came home, a print had finished just fine.. Went to do second print and the bed wouldn't start heating up. Can't see the light come on to try to pre heat...
Referral from April 25, 2017
Deem I. asked:
[Solved]
Extruder not heating... any tips?
Edit: for anyone else who encounters this issue - refer to Sean Rankin's comment below
Solution: take heater apart and rewire...
Referral from May 20, 2017
Jackson S. asked:
so recently ive been having trouble with my extruder not heating up and i found that there was a grub screw on the heat block that locks the heating element in place and...
Referral from August 31, 2017
David E. asked:
OK so everyone was talking about how the heatbed unit shorts out. Mine didn't short it just DIED. Thermistor is fine. Heating element shows infinite resistance. Makes no...
Referral from October 14, 2017
Devin N. asked:
After two failed overnight prints due to the hot end temp becoming too cool. My extruder wont heat up. I tried putting on the heating wires on again as well as the...
Referral from March 21, 2018
Bryson H. asked:
My heating block and red wire keeps melting my cooling fan duct. Now my prints are separating at the layers. Anyone know how to fix this or a stl file for a duct?
Referral from January 3, 2017
Christian D. asked:
I was wondering if anyone else has trouble with the A8 heat bed heating to over 99 degrees? Mine will only go to 97-99 degrees, even though I set it to 110 degrees. I...
Referral from January 23, 2017
Bud M. asked:
Where can I get replacement parts? I need a new nozzle, heating block and tube to feed the PLA.
Referral from February 20, 2017
Jacob T. asked:
Hey guys, been reading a bit lately after a mate bought a Anet A8 so I followed suit. Mine is yet to arrive but have already sorted a new psu and will see an electrician...
Referral from March 10, 2017
Kyle D. asked:
Gear Best is shipping crap. First a bad power supply, and now I need a new extruder as mine has no inner lining and the heating element set screw was tapped...
New Review
Please wait....
Please wait...
